Descripción
DESCRIPCION:
El Cisco 1005 es un simple router de escritorio que conecta pequeños sitios remotos, con ethernet LANs, a oficinas regionales o centrales mediante conexiones WAN.
CARACTERISTICAS:
PUERTOS:
- 1 Ethernet 10 Base-T (RJ-45)
- IOS Versión: 11.1 ( 6 )
- Memoria Física: 4Mb
- 1 Puerto para consola (RJ-45)
- 1 Puerto en serie (DB-60) que soporta los siguientes tipos de conexion WAN:
- Conexiones permanentes y de cambios sincrónicos WAN con velocidad máxima de 2.048 Mbps
- Conexiones WAN EIA/TIA-232 asincrónicas con velocidad máxima de 115.2 Kbps
- Un slot opcional para una tarjeta de memoria Flash PCMCIA
- Software de arranque que utiliza TFTP (Trivial File Transfer Protocol) sobre una conexión Ethernet LAN o sobre la memoria Flash PCMCIA
- Internet Protocol (IP), Internet Packet Exchange (IPX) y AppleTalk routing
- Soporte para: Protocolo Point-to-Point (P2P), High-Level Data Link Control (HDLC), Link Access Procedure Balance(LAPB), Frame Relay, Switched Multimegabit Data Service(SMDS) y X.25
- Configuración del router mediante el puerto de consola o sobre a través de la red utilizando el Simple Network Management Protocol (SNMP) ó Telnet
- Voltaje: 100-240 VAC a 50 - 60 Hz., 1.0A
- Memoria: 4-MB DRAM - SIMM, 1-MB boot PROM, 8-kb NVRAM
Show versión
IOS (tm) 1000 Software (C1005-XY-M), Version 11.1(6), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 09-Sep-96 13:29 by tej
Image text-base: 0x02004000, data-base: 0x02241CAC
ROM: System Bootstrap, Version 5.3.2(9) [vatran 9], RELEASE SOFTWARE (fc1)
ROM: 1000 Bootstrap Software (C1000-RBOOT-R), Version 10.3(9), RELEASE SOFTWARE
(fc1)
Router uptime is 8 minutes
System restarted by power-on
System image file is "flash:c1005-xy-mz.111-6", booted via flash
cisco 1000 (68360) processor (revision @) with 3584K/512K bytes of memory.
Processor board ID 04608016
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface.
1 Serial network interface.
8K bytes of non-volatile configuration memory.
2048K bytes of processor board PCMCIA flash (Read/Write)
Configuration register is 0x2102
Shielded Serial Transition Cable Pinouts
The serial port on the router uses a universal port, a 60-pin receptacle that supports the following serial interfaces: EIA/TIA-232, EIA/TIA-449, X.21, V.35, and EIA-530. The shielded serial transition cable determines the electrical interface type. The router end of all of the cables is a 60-pin connector.
DTE connectors have a plug connector at the network end. (DCE connectors have a receptacle at the network end.) However, V.35 is available in DTE mode with a connector of either gender at the network end. The serial port operates in DTE mode only.
The tables that follow list the signal pinouts for the DTE mode serial transition cables for each router interface type.
MANUALES Y DRIVERS
| Troubleshooting the Cisco 1005.pdf |  |
 |
Comentarios de visitantes
Si desea hacer un comentario sobre este producto, para ser leído por otros usuarios de la comunidad, por favor ingrese aquí